Need your washer dryer repaired by trusted experts?
You’ve come to the right place. Our engineers have specialist knowledge of all washer dryers allowing them to provide you with a quick, efficient and professional service.
Washer Dryer Repair Service in Nairobi
With a 1 year guarantee on all parts and labour, you can rely on Easy Repair Nairobi to provide the best solution to your repair needs, with flexible 2 hour and even weekend slots available for your convenience. Our team can even call ahead 30 minutes before we arrive so you won’t miss our visit.
Get an expert engineer to look after your repair
A broken washer dryer can be stressful, so we’ve made it quick and easy to book a repair.
Common Washer Dryer Faults We Repair
Experience has shown us that hobs can go wrong for a wide range of reasons, but we also see a number of very common washer dryer faults. Below are 3 common problems:
Washer Dryer is Leaking
The door seal, sump hose or pump could be leaking, Defective drain hose.
Washer/Dryer Doesn’t Dry
Door not shut, Faulty interlock, No power, Faulty on/off switch, Water supply disconnected or off, Water overheating due to faulty programmer, Worn motor brushes, Faulty timer, Door interlock faulty
Washer Dryer is not draining
Check the seals and gaskets. If they aren’t intact, call a technician to repair the issue. Also, check the drain hose and pipe to see if there is buildup that needs to be cleared.
Other Common Washer Dryer Faults
This list covers other common washer dryer faults we repair:
Washer Dryer Faults We Repair
Door gasket replacements
Dead
Leaks
No drum rotation
Blocked pumps
Noisy
Poor wash results
Not spinning
Not heating
Not draining
Pressure system faults
Faulty door
Display error codes
Snapped belts
Soap dispenser
Door seal
Smelly
Problems with spin cycle
And many more!
Easy Repair Nairobi is on hand to help repair all of these common washer dryer problems and more. Be sure to reach out today at 0208 343 2509 or get a quote online.
Washer Dryer Brands We Repair
Perhaps the most common appliance repair we carry out at Easy Repair Nairobi, washer dryer repair and service requires the attention of experienced professionals. Our team of local engineers are fully trained to carry out repairs on integrated and built-in washer dryers from an extensive range of manufacturers, including Bosch, Blomberg, Samsung, Hotpoint, Indesit, Beko, LG, Hoover, AEG, Electrolux, Hoover, Candy, Caple, CDA, Zanussi, NEFF, Sharp, Siemens, Smeg, Whirlpool, Amica, Baumatic , Belling, Fisher & Paykel, Hisense, Leisure, Miele, Stoves, Lamona, Whirlpool, Zanussi and many more.
Why Book an Appliance Repair with Easy Repair Nairobi?
Here are six of the top reasons why we’re considered among the leading appliance repair companies in Nairobi:
Fast and Reliable
Our fast and reliable service sets us apart: we meet 99% of our same-day/next-day appointments in Nairobi!
Fully Stocked Vans
Why wait for a part? Your technician will arrive in a fully stocked van, minimising the need for repeat visits.
Transparent Prices
Our quotes include fixed labour fees, covering unlimited repair time and repeat visits, with only parts charged on top.
Nairobi’s Repair Specialists
We have a team of Nairobi-based engineers, meaning we can offer top-notch service – with a local touch.
Comprehensive Services
We repair washing machines, dishwashers, ovens, cookers, hobs, fridges, freezers, fridge freezers, tumble dryers and washer dryers!
1-Year Guarantees
Our 1-year parts and labour guarantees mean that you’ll enjoy total peace of mind when you choose Easy Repair Nairobi.
Need your tumble dryer repaired by trusted experts?
You’ve come to the right place. Our engineers have specialist knowledge of all tumble dryers allowing them to provide you with a quick, efficient and professional service.
Tumble Dryer Repair Service in Nairobi
With a 1 year guarantee on all parts and labour, you can rely on Easy Repair Nairobi to provide the best solution to your repair needs, with flexible 2 hour and even weekend slots available for your convenience. Our team can even call ahead 30 minutes before we arrive so you won’t miss our visit.
Get an expert engineer to look after your repair
A broken tumble dryer can be stressful, so we’ve made it quick and easy to book a repair.
Common Tumble Dryer Faults We Repair
Experience has shown us that tumble dryers can go wrong for a wide range of reasons, but we also see a number of very common tumble dryer faults. Below are 3 common problems:
No functions
No power to appliance, Door switch faulty, Timer switch faulty, Delay timer faulty
Timer turns, but no drum rotation
Drum motor faulty, Drum belt snapped, Timer switch faulty, Reversing timer faulty (if fitted)
Clothes not drying, but drum and timer both turn
Thermostat faulty, Heating element faulty, Thermal cut-out fuse operated
Other Common Tumble Dryer Faults
This list covers other common tumble dryer faults we repair:
No power
Snapped belt
No heat
Overheating or burning
Poor drying
Blockages
Drum not spinning
Noisy
Condenser drawer issue
Leaking
Tripping electrics
And many more!
Easy Repair Nairobi is on hand to help repair all of these common tumble dryer problems and more. Be sure to reach out today at 0208 343 2509 or get a quote online.
Tumble Dryer Brands We Repair
We are an approved service centre for a large number of leading tumble dryer manufacturers, including AEG, Electrolux, Bosch, Neff, Siemens, Miele, Smeg, Samsung, LG, Candy, Hoover, Baumatic, Hotpoint, Indesit, De Dietrich, Caple, CDA, Amica, Bauknecht, Beko, Belling, Blomberg, Gorenje, Lamona, Whirlpool, Zanussi and many more, meaning you’re sure to find the solution to your repair needs with Easy Repair Nairobi.
Why Book an Appliance Repair with Easy Repair Nairobi?
Here are six of the top reasons why we’re considered among the leading appliance repair companies in Nairobi:
Fast and Reliable
Our fast and reliable service sets us apart: we meet 99% of our same-day/next-day appointments in Nairobi!
Fully Stocked Vans
Why wait for a part? Your technician will arrive in a fully stocked van, minimising the need for repeat visits.
Transparent Prices
Our quotes include fixed labour fees, covering unlimited repair time and repeat visits, with only parts charged on top.
Nairobi’s Repair Specialists
We have a team of Nairobi-based engineers, meaning we can offer top-notch service – with a local touch.
Comprehensive Services
We repair washing machines, dishwashers, ovens, cookers, hobs, fridges, freezers, fridge freezers, tumble dryers and washer dryers!
1-Year Guarantees
Our 1-year parts and labour guarantees mean that you’ll enjoy total peace of mind when you choose Easy Repair Nairobi.
Seeking microwave oven repair Nairobi experts? Chances are that there’s a problem with your microwave oven. It may be not heating the proper way. It may be too noisy. Or, it may be sparking and smoking. In any case, stop worrying about it! Our company has solutions to all kinds of issues.
The best part about our microwave oven repair services in Nairobi ? We can provide them the moment you need it the most. So, what’s the point in stressing over a faulty timer or poor heating? If you are in Nairobi, Kenya, simply make contact with us and get a top-notch microwave oven service.
Fast Services in microwave oven repair in Nairobi. Work with us !
When it comes to microwave repair, there’s no room for mistakes. Of all the appliances, microwaves are probably the most complex ones. What’s more, they are potentially dangerous. So, don’t take any risks! For your own peace of mind, entrust the job to our team.
We assign all such requests to the finest local techs. All of them are experienced, trained and updated with the industry novelties. So, let nothing concern you! Minor or major, any microwave repair service will be carried out quickly and in a safe & accurate way.
You can count on us for any Microwave Oven Repair service at all
What’s your current microwave service request? Do you need the appliance fixed? Perhaps, you want it tuned-up? Or maybe, you’ve got a new over-the-range model and planning to have it installed? Here’s the good news for you! Our company can be of help with any microwave service in Nairobi.
Not only can you call us for repairs but also for routine check-ups and install jobs. So, what’s there to even think about? If it’s time for Nairobi microwave repair or you are looking for any other service, let us know!
Microwave Oven Parts that We Repair
Microwave Oven Repair services in Nairobi Kenya. Is your microwave oven broken? Is it not turning on? Not heating, broken glass, broken hotplate? We fix microwave ovens in Nairobi. Call us for service.
MICROWAVE OVEN MEMBRANE SWITCH
If the touch pads on your microwave oven do not respond but the display lights up, the problem is most likely with the membrane switch. This component, which is more commonly referred to as the touch pad, is actually a series of soft touch electrical switches.
It is usually made up of two layers of a thin Mylar plastic with a conductive material on the inner surfaces. A formed gap between the two surfaces will separate the conductive coatings until pressure is applied by the user, making the two surfaces come in contact. When the two conductive surfaces contact each other, an electrical circuit is completed to provide an input signal to the control board.
With repeated use, the conductive coating will eventually wear out and be unable to make a good enough contact to send the signal to the control board. To access the membrane switch you will need to unplug the unit and remove the cabinet. The membrane switch is often attached to the control panel and is usually connected to the electronic control board with a flat ribbon style connector.
Check the connection first and if it appears okay, then you can test the membrane switch for continuity with a multi-meter. There should only be a few ohms of resistance for each touch pad when pressed. To perform this test you will require the matrix layout of the membrane switch which should be contained in the electrical schematic.
MICROWAVE OVEN CONTROL BOARD
If the touch pads on your microwave oven do not respond but the display lights up, the problem may be with the control board. The control board generates a low voltage that is supplied to the membrane switch. When a pad is depressed, the voltage signal is switched back to the control board.
The control board receives these input signals from the membrane switch or touch pad and uses these commands to turn on output relays that control the various components of the microwave, such as the turntable motor and the magnetron. If the control board does not generate the low voltage signal, or if it does not sense the input signals from the membrane switch, then no output functions will occur.
If you have verified that the membrane switch is fine and the connection to the control board is okay, then the control board may be defective. Replacement will require disconnecting the power and removal of the cabinet and control assembly.
MICROWAVE OVEN DRIVE MOTOR
If the turntable on your microwave is making an unusual noise, the problem may be with the drive motor. Most microwave ovens with a glass tray use a motor driven coupler to turn the tray or a roller guide. The motor is typically located below the floor of the oven, and access will need to be through the bottom. The motor is normally held in place with a retaining screw and will have two wires attached to it as well. If the motor is making a grinding noise it will need to be replaced.
MICROWAVE OVEN MAGNETRON
If your microwave is making an unusual or loud humming noise, you may have a problem with the magnetron. This component is part of the high voltage circuit and provides the microwaves that generate the heat. If the magnetron is defective, it may cause a loud humming or buzzing noise.
Access to the magnetron will require removal of the cabinet. Disconnect the power and also discharge the high voltage capacitor to prevent an electrical shock. You can then locate the magnetron and disconnect the two attached wires and the mounting screws to remove it. You should also check the high voltage diode to verify that it is not shorted before condemning the magnetron.
MICROWAVE OVEN DRIVE COUPLER
If your microwave is making an unusual noise, the problem may be with the drive coupler for the turn tray. Most microwave ovens with a round glass tray use a motor driven coupler to rotate the tray on a roller guide. Some models that use a rectangular tray will have a drive coupler that has an offset center roller to drive the tray guide from side to side.
For either style, remove the tray and roller guide from the oven and then inspect the coupler. Some models may require you to remove the motor from the bottom before you can pull the coupler off of the motor. The coupler normally has a D shaped opening that fits tightly onto the motor shaft. If it is cracked or worn it may become noisy and will need to be replaced. If you have to remove the bottom cover, you will need to disconnect power from the appliance first.
MICROWAVE OVEN ROLLER GUIDE
If your microwave is making an unusual noise when the turn tray is rotating, the problem may be with the roller guide under the tray. Some microwave ovens with a round glass tray use a motor driven coupler to turn the roller guide. The roller guide is used to support the tray and to engage the rotating coupler. Remove the tray and then inspect the roller guide.
Check the hub to see if it engages the coupler securely and also the outer rollers for signs of cracks or damage. If there are signs of wear or damage, it should be replaced. Other models may just use the roller guide to support the tray, however the roller wheels may be damaged or worn and causing an unusual noise. If the roller guide appears to be normal, then check the coupler for damage.
MICROWAVE OVEN HIGH VOLTAGE DIODE
If your microwave is making an unusual or loud humming noise, you may have a problem with the high voltage diode. This component is part of the high voltage circuit along with the capacitor and the magnetron. Access to the diode will require removal of the cabinet.
Disconnect the power and also discharge the high voltage capacitor to prevent an electrical shock. You can then locate the diode and use a multi-meter to check for continuity. Reverse the meter leads to check for continuity in the opposite direction. There should be continuity in only one direction and if not, it will have to be replaced.
MICROWAVE OVEN COOLING FAN
If your microwave is making an unusual noise, the problem may be with the cooling fan. The cooling fan is located inside the cabinet and is used to cool the magnetron. Disconnect the power and then remove the cover and locate the fan assembly. Inspect the housing for any foreign objects that may contact the fan blades and then check the
MICROWAVE OVEN DOOR INTERLOCK SWITCH
If your microwave oven doesn’t appear to shut off when the door is open, you may have a problem with the door switch. The door switches, often referred to as interlock switches, provide power to the various components of the microwave. They are designed to interrupt the power when the door is open.
In certain situations when an interlock switch fails, the interior light, fan motor, or stirrer motor may continue to operate after the microwave oven door is opened. The magnetron will not operate because of a failsafe monitor switch. The interlock switches are located inside the cabinet and are activated by hooks or latches on the door. Unplug the unit and remove the cabinet.
The interlock switches will have wires attached to the terminals marked common (C) and normally open (NO). You can check the switches for continuity using a multi-meter. The closed door will depress the actuator button on the switch; you should see continuity between these terminals. When the door is open there should be no continuity, and if there is the switch needs to be replaced.
MICROWAVE OVEN SMART BOARD
If your microwave oven doesn’t shut off until the door is opened, you may have a problem with the control board. The control board, sometimes referred to as the Smart Board, powers the relays that control the various functions of the microwave.
If the control is defective it may not shut off a relay when the function is complete, and then opening the door to interrupt the power to the control would be the only way to terminate the cycle. If you have this symptom, the control board may be at fault. Unplug the unit and remove the cabinet.
If the relays are not part of the control board, you should check the output terminals on them for continuity first. There shouldn’t be continuity when the relay is not powered. If the relays check okay, then the control board is likely defective.
MICROWAVE OVEN HIGH VOLTAGE DIODE
If your microwave oven doesn’t heat, you may have a problem with the high voltage diode or rectifier. This component helps provide the high voltage that powers the magnetron. The high voltage diode is located near the magnetron and the high voltage capacitor, so access will require removal of the cabinet.
Disconnect the power and also discharge the high voltage capacitor to prevent an electrical shock. You can then test the diode for continuity with a multi-meter. Diodes are polarity specific and you should see low resistance with the meter leads in one direction and higher resistance when the meter leads are reversed. Most multi-meters will have a special setting for diodes or rectifiers.
If the high voltage diode shows low resistance in both directions or shows no continuity at all, then it will need to be replaced. If you find the high voltage diode tests okay, then you will need to determine whether power is being supplied to the circuit. This is a high voltage circuit and further testing should only be performed by a qualified technician.
MICROWAVE OVEN DOOR SWITCH
If your microwave oven doesn’t heat, you may have a problem with a door switch. The door switches, often referred to as interlock switches, provide power to the various components in the microwave when the door is in a closed position, and interrupt power when the door is open. Sometimes it is possible that when an interlock switch fails, the fan motor and or stirrer motor may continue to operate but the magnetron won’t.
The interlock switches are located inside the cabinet and are activated by hooks or latches on the door. Unplug the unit and remove the cabinet. The interlock switches will have wires attached to the terminals marked common (C) and normally open (NO).
Check the switches for continuity using a multi-meter. With the actuator button depressed, you should see continuity between these terminals. If there is no continuity the switch will need to be replaced. You should also verify that the door hooks properly engage the switch actuator when the door is closed and adjust if necessary.
MICROWAVE OVEN MAGNETRON
If your microwave oven doesn’t heat, you may have a problem with the magnetron. This component is part of the high voltage circuit and provides the microwaves that generate the heat. If the magnetron is defective, the unit may blow a fuse, or you may still have all other functions operating normally.
Access to the magnetron will require removal of the cabinet. Disconnect the power and discharge the high voltage capacitor to prevent an electrical shock. You can then locate the magnetron and disconnect the two attached wires. Attach the leads from a multi-meter to the magnetron terminals and check for continuity.
There should be only 2-3 ohms of resistance between these terminals. If there is no continuity, then the magnetron will need to be replaced. Also, check for continuity between both terminals and the grounded outer case of the magnetron. If there is any continuity between either of the terminals and ground, the magnetron will need to be replaced. If the continuity checks do not reveal any defects, then live voltage tests may be required and should be referred to a qualified person.
MICROWAVE OVEN DOOR LATCH LEVER OR BUTTON
If the door on your microwave oven won’t open, you may have a problem with the door latch lever. The door latch lever assembly usually consists of a paddle or button that either pivots downward or pushes into the control panel. It then contacts the door latch assembly and releases the door hooks to allow you to open the door. If the pivot or lever portion is broken, then the door hooks cannot be lifted to release the door.
Unplug the unit and remove the cover to access the door latch lever. You may also need to remove the control panel to gain better access. Remove the broken piece and insert the new part into the pivot openings. On models that use a push button style, release the retaining tabs and install the new part making sure that the return spring is installed correctly.
MICROWAVE OVEN DRIVE MOTOR
If the turntable on your microwave doesn’t rotate or is making a grinding noise, the problem may be with the drive motor. Most microwave ovens with a round glass tray use a motor driven coupler to turn the tray or a roller guide. The motor is typically located below the floor of the oven, and access will need to be through the bottom.
The motor is normally held in place with a retaining screw and will have two wires attached to it as well. If the motor is making a grinding noise it will need to be replaced. If the motor doesn’t turn, you can check for voltage or continuity with a multi-meter. With the power disconnected and the bottom panel removed, locate the motor and unplug the wires to the motor.
Measure for continuity at the motor terminals or at the wire harness that is still attached to the motor. If there is no continuity, the motor will need to be replaced. For voltage checks, you will need to plug the unit into a live outlet and therefore this check should only be performed by a qualified person.
MICROWAVE OVEN COUPLER
If the turntable on your microwave doesn’t rotate, the problem may be with the drive coupler. Most microwave ovens with a round glass tray use a motor driven coupler to turn the tray on a roller guide. Some models that use a rectangular tray will use a drive coupler that has an offset center roller to drive the tray guide from side to side.
For either style, remove the tray and roller guide from the oven and then inspect the coupler. Most models will have a three sided coupler that will just pull off of the motor shaft. Some models may require that you remove the motor from the bottom before you can pull the coupler off of the motor.
The coupler normally has a D shaped opening that fits tightly onto the motor shaft and if it is cracked or worn it will need to be replaced. If you have to remove the bottom cover, you will need to disconnect power from the appliance first.
MICROWAVE OVEN ROLLER GUIDE
If the turntable on your microwave doesn’t rotate, the problem may be with the roller guide under the tray. Some microwave ovens with a round glass tray use a motor driven coupler to turn the roller guide that the tray rests on. The roller guide is used to support the tray and to engage the rotating coupler.
Remove the tray and then inspect the roller guide. Check the hub to see if it engages the coupler securely and also the outer rollers for signs of cracks or damage. If there are signs of wear or damage, it should be replaced. If the roller guide appears to be normal, then check the coupler for damage.
MICROWAVE OVEN CHARCOAL FILTER
If the exhaust fan on your over-the-range microwave is not working, the problem may simply be the charcoal filter. The charcoal filter is used to trap and absorb cooking smells when no external vent system is used. Over time, the charcoal filter will become clogged and restrict the air flow.
The charcoal filter is normally located behind the exhaust air outlet grill. You can typically detach the grill by removing some retaining screws and then remove and replace the charcoal filter which may also have a spring clip to hold it in place. Replace the charcoal filter on a regular basis to maintain a good airflow. You should also check the condition of the primary grease filter as well.
MICROWAVE OVEN GREASE FILTER
If the exhaust fan on your over-the-range microwave is not working, the problem may simply be the grease filter. The grease filter or filters are used to trap cooking oils and fats to prevent contamination of the exhaust system. With normal use, the grease filters will become clogged and restrict the air flow.
Normally, the grease filters are located on the bottom of the microwave and are held in place with spring clips or tabs for easy removal. Regular cleaning of the grease filters in hot water and detergent will help maintain proper airflow, however, if the filters are very dirty or damaged they should be replaced. If an external exhaust system is not used, you should also inspect the internal charcoal filter.
MICROWAVE OVEN DAMPER ASSEMBLY
If the exhaust fan on your over-the-range microwave does not appear to be working, the problem may be with the damper assembly. If you are connected to an external exhaust system, the damper is used to prevent unwanted outside air from entering the room. The damper is basically a metal or plastic flapper that closes off the exhaust duct when the fan is not running, and opens when the fan turns on.
The damper may have a spring assisted flapper or it may rely on gravity to keep it closed when the fan is not in use. If the damper does not open easily or completely, then the airflow may not be sufficient to remove steam or cooking smells. The damper is located at the exhaust outlet of the microwave and removal from the wall or cabinets may be necessary.
Verify that no foreign objects or the exhaust duct connector are interfering with the damper. Replace the damper if it appears to be damaged or does not open and close easily. When re-installing the vent connector, make sure there is no interference with the damper.
MICROWAVE OVEN FAN MOTOR
If the exhaust fan on your over-the-range microwave does not appear to be working, the problem may be with the fan motor. The fan motor is located at the top rear of the microwave and exhausts the air into the duct system or re-circulates into the room through the charcoal filter depending on the installation.
If the fan motor does not turn on when selected, you will need to disconnect the power and remove the unit from the wall or cabinet to service. Remove the cover and locate the fan motor. Rotate the motor by hand. If the motor will not turn, it needs to be replaced. If the motor turns freely, you can check the motor for continuity with a multi-meter and if no continuity is found, you will need to replace the motor.
If the motor does show continuity, the next step would be to check for power to the fan motor. This is a live voltage test and should only be performed by a qualified person. If the correct voltage is available, then the motor is likely defective. If no voltage is detected, the problem may be with the wiring or the electronic control board.
MICROWAVE OVEN DOOR SWITCH
If your microwave oven won’t start, you may have a problem with a door switch. The door switches, often referred to as primary or secondary interlock switches, provide power to the various components in the microwave when the door is in a closed position, and interrupt power when the door is open.
Sometimes it is possible that when a door switch fails, the display and controls may appear normal, but the oven won’t operate. The interlock switches are located inside the cabinet and are activated by hooks or latches on the door. Unplug the unit and remove the cabinet. The interlock switches will have wires attached to the terminals that are marked common (C) and normally open (NO). You can check the switches for continuity using a multi-meter.
With the actuator button depressed, you should see continuity between these terminals. If there is no continuity the switch will need to be replaced. You should also verify that the door hooks properly engage the switch actuator when the door is closed and adjust or replace it if necessary.
MICROWAVE OVEN CERAMIC FUSE
If your microwave oven won’t turn on and the display is blank, the problem may be the ceramic fuse. The ceramic fuse is used to protect the components of the microwave oven if you have a severe power fluctuation or if there is a critical fault with one of the internal components.
When the fuse fails, power is interrupted to the controls of the microwave and it will become nonfunctional. The ceramic fuse is located inside of the cabinet near the entry point of the power cord. Remember to unplug the cord before attempting any repairs. You can check the fuse for continuity with a multi-meter.
If the fuse failed for no apparent reason, check the major components such as the magnetron, high voltage diode, capacitor and transformer, and associated wire terminals, before changing the fuse. If the fuse failed when opening or closing the door, check for a shorted door switch, monitor switch, or improper adjustment of the door latch assembly. Use only the manufacturers’ suggested part number when replacing this fuse.
MICROWAVE OVEN THERMAL FUSE OR CUT OUT
If your microwave oven won’t turn on, you may have a problem with the thermal cut-out. Microwave ovens use one or more thermal cut-outs, sometimes called thermal fuses, to protect the oven from overheating. They are located inside of the cabinet, often near the oven cavity or the magnetron. If the thermal cut- out fails, power is interrupted to the controls or to the control outputs.
Unplug the unit and remove the cabinet. Locate the thermal fuse or cut-out and remove the wires from the terminals. Check for continuity with a multi-meter and replace the part if no continuity is shown. Verify that the cooling fan is functional and that the air flow is not restricted.
MICROWAVE OVEN DOOR LATCH ASSEMBLY
If your microwave oven won’t turn on, you may have a problem with the door latch assembly. The door latch assembly usually consists of two hooks that protrude from the door and fit into the door switch holder that is mounted to the frame of the microwave.
The hooks will contact the door switches to provide power to the controls and also, latch onto the holder to keep the door closed. The latch assembly is normally made of plastic and usually has a spring attached to provide downward tension to keep the hooks engaged. If either of the hooks is broken or does not have any spring tension, the switches may not be engaged.
If this happens, the oven won’t turn on and you may need to replace the assembly. Unplug the unit and remove the inner door panel to access the door latch. The inner panel is normally attached by plastic tangs and caution should be used to remove it.
MICROWAVE OVEN DOOR LATCH ASSEMBLY
If the door on your microwave oven doesn’t appear to close properly, you may have a problem with the door latch assembly. The door latch assembly usually consists of two hooks that protrude from the door and fit into the door switch holder that is mounted onto the frame of the microwave.
The hooks will contact the door switches to provide power to the controls and also latch onto the holder to keep the door closed. The latch assembly is normally made of plastic and usually has a spring attached to provide downward tension to keep the hooks engaged.
If either of the hooks is broken or does not have any spring tension, you may need to replace the assembly. Unplug the unit and remove the inner door panel to access the door latch. The inner panel is normally attached by plastic tangs and caution should be used to remove it.
MICROWAVE OVEN TORSION SPRINGS
If the door on your microwave oven doesn’t appear to close properly, you may have a broken torsion spring. On microwaves that have a door that opens downward, torsion springs are used to keep it closed. There are normally a left and right side spring and they are often different sizes.
If your door won’t stay closed, one of the springs may have broken. Unplug the unit and remove the inner and outer door panels to access the torsion springs that are located at the bottom front of the door. Depending on the model involved, the panels may be held in place with screws from the inside, bottom, or sides. Use caution as the outer glass door may be heavy.
Easy Repair offers Television repair services in Nairobi. Our TV repair technicians and fundis are trained, experienced and skilled. Trust us with all your TV Repairs. We Repair all brands and makes of televisions, Hi-Fi, DVDs, Inverters and Elecronic mother boards. Call Easy Repair Nairobi today for professional TV repairs.
For Reliable and affordable Television Repair services in Nairobi Kenya
Trust us with all your TV Repairs. We Repair all brands and makes of televisions, Hi-Fi, DVDs, Inverters and Elecronic boards. Call Easy Repair Nairobi today for professional TV repairs.
LG TV / Television Repairs / Service
Samsung TV / Television Repairs / Service
Sony TV / Television Repairs / Service
Sinotec TV / Television Repairs / Service
Panasonic TV / Television Repairs / Service
Toshibia TV / Television Repairs / Service
TCL TV / Television Repairs / Service
Hisense TV / Television Repairs / Service
And more brands
TV Repairs – Nairobi
Tv repairs, Plasma repairs, LCD Repairs, 3D Smart tv LED Repairs – Westlands
Tv repairs, Plasma repairs, LCD Repairs, 3D Smart tv LED Repairs – Muthaiga
Tv repairs, Plasma repairs, LCD Repairs, 3D Smart tv LED Repairs – Athi River
Tv repairs, Plasma repairs, LCD Repairs, 3D Smart tv LED Repairs – Lavington
Tv repairs, Plasma repairs, LCD Repairs, 3D Smart tv LED Repairs – Spring Valley
Tv repairs, Plasma repairs, LCD Repairs, 3D Smart tv LED Repairs – Runda
Tv repairs, Plasma repairs, LCD Repairs, 3D Smart tv LED Repairs – Karen
Tv repairs, Plasma repairs, LCD Repairs, 3D Smart tv LED Repairs – Kileleshwa
Tv repairs, Plasma repairs, LCD Repairs, 3D Smart tv LED Repairs – Thika Road
Tv repairs, Plasma repairs, LCD Repairs, 3D Smart tv LED Repairs – Embakasi
Tv repairs, Plasma repairs, LCD Repairs, 3D Smart tv LED Repairs – Machakos
Tv repairs, Plasma repairs, LCD Repairs, 3D Smart tv LED Repairs – Kikuyu
Tv repairs, Plasma repairs, LCD Repairs, 3D Smart tv LED Repairs – Langata
Tv repairs, Plasma repairs, LCD Repairs, 3D Smart tv LED Repairs – Limuru
Tv repairs, Plasma repairs, LCD Repairs, 3D Smart tv LED Repairs – Ngong
Are you looking for the best Tv repair services in your area?You can rely on our well trained TV technician at Nextgen Solutions.You could also be wondering “do you have TV repair services near me or in my area?. Yes we do as we will connect you to near by well trained TV technician or send you one from Nairobi.You can Schedule service online today, or give us a call at 0706731791 0737678617.
TV is one among the foremost important home appliances now days. It’s not only source of stories but also for entertainment. We understand that it are often very disappointing when your TV broke up. But you don’t need to hand over so fast on your broken TV.As we are here to assist you. Give us call today or contact via email with the model number found on the box you purchased the TV or on the rear of your TV. If you’re you trying to find TV repairs services near me In Nairobi, Kenya. We are here as we provide service in your area.
TV repairs services near me
Appliance RepairsTV Repair Services Provider Near Me
We have been providing prompt, professional Television Repair Service in Nairobi, Kenya. we offer services altogether Nairobi estate like Lavington, Karen,Runda,Muthaiga,Kilimani,Kileleshwa,Ridgeways,Parklands,Umoja,Buruburu,South B,South C,Ngong,Kitengela,Mlolongo etc.If you’re you trying to find TV repairs services near me we are in your are.
TV Repair Services Shop Near Me In Nairobi
Whether your TV is modern or old one. Big or small one. We got you as our highly trained and authorized TV repair technicians can meet all of your needs. We understand how troublesome it’s to hold your TV from you home to the repair center. Due to this we’ve onsite repair services. You’ll trust our highly trained technician to diagnose and fix any issue.
Fast, Reliable TV Repair Service!
You can call us for TV Repairs Service in your area. We’ll make certain to reply to you within a 24-hour.And if our any technician is out there you’ll get same day services.
Common Issues That We Fix
A faulty TV are often a source of frustration, leading to you missing favorite programs or witnessing a bubbling screen. There are some simple repair you’ll do on your own. But this is often as long as the matter may be a general one. Except for complicated TV Repair Services in Nairobi Kenya leave them to specialist. Your TV has lines or is cracked.
TV screen Replacement services in Nairobi
This can be caused by two things. One is either you TV screen have Psychical damage or there’s a defective part. If the screen is physically cracked there’s no repair for that the screen got to get replaced. But don’t we go screen of all sizes and every one brands. Just call us with model number and that we will allow you to know the worth.
Best TV back lights repair services in Nairobi,Kenya
TV Has Different Color Vertical Lines on Screen
tv repair services with vertical lines
This is often a really common issue with many TVS. When you’re TV have a vertical colored lines it means the T-Con isn’t working well. It’s going to be that there’s loses connection. Also sometimes the T-Con got to get replaced.
TV shows a blue, green, or black screen.
tv repair with vertical lines
This is can occur when your TV isn’t getting a sign. To repair this confirm that your cable is powered on which the TV is about to the right input.
LED TV has Horizontal lines on start-up
Tv repiar services with horizontal lines
The root problem is low signal strength within the set-top box cable that’s connected to you LED TV. This problem occur mostly with the fashionable TV because they required strong input signals compare to the older TVs. to repair this you would like to modify to an HD set-top box which can most likely rectify the matter.
LED TV screen goes blank
black screen TV repair services
This can be occur if your back-lights aren’t working well. But if they’re working well and there’s no image on the screen. This suggests the matter is either the t-con board or the most board. It’s recommended to seek out a technician to return and replace the back-lights or the T-con.
TV will activate from the remote, but not the cable or satellite box.
It occurs when the cable box isn’t passing signal to your TV properly. To repair this unplugging the box off for 15 seconds. And turning it back on again.
Cracked TV Screen Repair Cost In Kenya
The cost of Cracked Tv screen replacement in Kenya depend on the TV model and the Inches. Send us your TV model to our whatsapp number 0706731791 or send message on this form
Samsung Cracked or Broken TV Replacement Services
cracked screen replacement services in kenyaHave your Samsung Tv Cracked or is broken. And you could be wondering “Can I get Samsung TV screen center near me”? Yes we can as we offer repair of all Samsung TV across Kenya.
Sony TV Repair Shop in Nairobi
Sony TV Repair services in Nairobi,Kenya
Are you looking for a Sony TV repair Shop in Nairobi. Look no more as Appliance Repairswe offer repair of all Sony TV from screen replacement to other services.
TV Repairs Services Provider Near Me
We’ll diagnose the issue and supply you an estimated cost of repair. Sometimes we could also be ready to fix the issue during the visit. Or we may have to order a neighborhood so we complete the repair subsequent day. We do everything we will to get it right. Until you’re satisfied with our services.
We do TV repair in Nairobi, Limuru, Thika, westland,Highridge, Parklands, Ngara, Pangan Avenue Park, Fedha, Pipeline, Donholm, Greenfields, Nyayo, Taasia, Baraka, Nairobi West, Madaraka, Siwaka, Lavington, Karen , Runda , Muthaiga , Kilimani , Kileleshwa , Ridgeways , Parklands , Umoja , Buruburu , Southh , Southh , Ngong , Kitengela , Mlolongoo et South B, South C, Mugoya, Riverbank, Hazina, Buru Buru, Uhuru, Harambe ,,Civil Servants, Akiba, Kimathi, Pioneer, Koma Rock, Umoja II, Kariokor, Dandora, Kariobangi, Kayole, Embakas , Hurumaa. Kitengela suburb, Ongata Rongai, Kiseria ,,Embulbul et
Our Service
Led TV repair in Nairobi, Samsung tv repair in Nairobi, TV repair home service Nairobi
TV repair reception in Nairobi,lcd TV repair Nairobi, TV repair service in Nairobi, Kenya,tcl tv repair in Kenya, Samsung tv repair center Nairobi, lg tv repair in Nairobi, screen replacement Kenya
This Fix-It Guide on television repair tells how a flat-screen or tube-type television works, what often goes wrong, how to identify a television problem, and what parts and tools you will need to fix it. It then gives simple step-by-step instructions for how to service a mechanical tuner and refers you to instructions for how to test and replace electronic components. Before calling the TV repair service, there are many things you can do yourself to eliminate or reduce the cost of technical repair. The tips in this Fix-It Guide apply to both flat-screen television repair and tube-type television repair. This guide also refers to other Fix-It Guides for dealing with common problems such as electrical cord repair, electrical receptacle repair, remote control repair, and others.
How Does a Television Work?
A television receiver is an electronic device that receives audio and video signals from an antenna, cable/satellite, or a video player and converts those signals into visible light rays and audible sound. A television receiver displays a picture as horizontal lines on the screen. Each line contains a series of red, green, and blue stripes. At viewing distance, the lines and stripes merge and we see a sharp picture in full color. Modern televisions rely on solid-state electronic components that require servicing by a trained technician.
Caution!
Don’t even mess with trying to fix a flat-screen TV. Leave service to a professional. Meantime, review the owner’s manual to determine the probable cause and solution. It may just be an adjustment that you can make.
What Can Go Wrong with a Television?
Components of a tube-type television receiver. Flat-screen televisions have miniature circuit boards that should only be repaired by an electronic technician.
Most problems that you can fix are caused by loose connections or improperly set controls. TVs made since about 1990 are often adjusted with a hand-held remote and on-screen commands. Finer adjustments can be made by a television service technician. Problems that appear suddenly indicate a failed component, especially if the set has recently been subjected to shock, vibration, or excessive heat. The picture and sound quality gradually deteriorate due to aging.
How Can I Identify a Television Problem?
There are many things you can do before calling for service. First, switch to a different channel or wait a few hours to see if the trouble might be with the cable/satellite service or the broadcaster. Get out your owner’s manual and make sure the controls are set properly. Make sure power is on to the electrical receptacle and test the electrical cord. In addition, check the remote control.
Most TVs have adjustments for brightness, color, and sound. Refer to the owner’s manual for adjustment instructions.
If there are color blotches in the image, they are usually caused by magnetization of the TVs metal parts or picture tube. Most sets have a built-in device for demagnetizing. Turn the set on for one to two minutes, then turn it off. Repeat several times at half-hour intervals. If this fails, demagnetize the picture tube by running a degaussing coil (available with instructions at electronics parts stores) across the tube with the set turned off.
If bright areas of a picture look silvery and details are indistinct, the picture tube is defective. When brightness is turned to low level, the picture will appear normal but dull. With brightness up, detail in white areas is lost. The picture may improve after the set has been on for an hour or more, but you’ll eventually have to replace the tube.
Fix-It Tip
How long should your television set last? TVs have an average life of three to eight years of moderate to heavy (eight or more hours per day) use. Most TVs typically last about five years. But many sets are still out there operating at 15+ years. Before investing in costly repairs, check the price of a replacement set. Television sound and picture have improved greatly and there are some good deals available.
What Do I Need for Television Repair?
Replacement parts are available from the manufacturer, aftermarket suppliers, and local electronic stores. The tools you will need to fix a TV include:
Screwdrivers
Wrenches
Tuner or electronic cleaner
What Are the Steps to Television Repair?
Refer to the Fuse Fix-It Guide and the Appliance Controls Fix-It Guide for information on testing and replacing electronic components.
Service a mechanical television tuner (solid-state tuners must be professionally serviced):
Remove the metal plate protecting the tuner, typically attached to the front of the cabinet.
To clean the contacts, carefully spray them with tuner or electronic cleaner, turning the channel selector to distribute the cleaner over the contacts.
If replacement is required, you may need to de-solder the unit to remove it (see the Fix Anything Fix-It Guide).
Fix-It Tip
Old TVs have vacuum tubes instead of solid-state components. You can purchase them through specialized parts suppliers and larger electronic stores.
Need your fridge freezer repaired by trusted experts?
You’ve come to the right place. Our engineers have specialist knowledge of all fridge freezers allowing them to provide you with a quick, efficient and professional service.
Fridge Freezer Repairs in Nairobi
At Easy Repair Nairobi, we provide professional fridge freezer repairs in Nairobi and surrounding areas.
Same-Day Fridge Freezer Repairs
Fridge freezers are a fantastic way to both chill and freeze food. But if your fridge freezer develops a fault, you’ll find yourself in a race to stop that food going off. Our same-day fridge freezer repair service could offer the perfect solution.
There When You Need Us
We’ll set up a convenient 2-hour repair slot, with the option of evening/weekend appointments. For your added convenience, your engineer will check that you’ll be there, by calling 30 minutes ahead of their visit.
Experts You Can Trust
Our team of engineers are the experts you can trust to get your fridge freezer working again – fast. Your engineer will begin by diagnosing the fault, and can advise you whether the problem can be resolved there and then. We stock our engineers’ vans with a variety of parts, and hold an even wider range in our local warehouse.
And you can rest assured that Easy Repair Nairobi is an F-Gas registered fridge freezer repair company, with a dedication to safety. As such, our engineers will follow up every repair with a safety check.
Freestanding and Integrated Fridge Freezer Repairs
Our Nairobi-based fridge freezer repair engineers are highly trained professionals with the experience needed to carry out both freestanding and integrated fridge freezer repairs.
We know that repairing integrated fridge freezers requires even more care, to avoid damage to your units; you can be confident that our engineers will treat your home and appliances with the respect they deserve.
American Style Fridge Freezer Repairs
We’re also experienced in American style fridge freezer repairs. Also known as ‘side-by-side’ fridge freezers, these large appliances are increasingly popular in Nairobi and the rest of the UK.
Brands We Repair
Our fridge freezer repair engineers routinely repair all major makes and models, including AEG, Samsung, LG, Siemens, Bosch, Liebherr, Neff, Rangemaster, Smeg, Miele, Gorenje, Hoover, Candy, Caple, Haier, Hotpoint, Indesit, Beko, CDA, Amica, Daewoo, Electrolux, Fisher & Paykel, Frigidaire, De Dietrich, Leisure, Lamona, Baumatic, Lec, Whirlpool, Stoves, Zanussi and many more.
Common Problems
As one of the leading independent fridge freezer repair companies in Nairobi, we know a lot about what can cause these appliances to fail. Below are three of the most common problems we encounter when performing same-day fridge freezer repairs.
Failure to Stay Cold
If your fridge freezer doesn’t stay cold, the thermostat or fan motor may have failed. It’s also possible that the compressor isn’t working correctly, or that ice has built up, impairing operation. Fridge freezers rely on many separate parts to stay cold, so it’s best to get a professional to diagnose the source of the problem.
Noisy Operation
Fridge freezers usually make a little noise – often a low background hum – but if your fridge freezer becomes noisier while operating, that could signal a fault. Some common causes include a failing fan motor, a build-up of ice against the fan, or a blockage of the air channels.
Excess Ice
Sometimes, excess ice can be a sign that warm air is getting into your fridge freezer (a damaged door seal is a common cause). This can also happen if the thermostat is failing to keep the appliance at the optimal temperature.
Other Problems
We’re happy to repair any of the following fridge freezer problems:
Dead
Electrical issues
Not freezing
Too cold
Frost build-up/freezing
Temperature irregularities
Faulty thermostat
Door seal issues
Faulty water dispenser
No light
Noisy
Leaks or puddles inside
Damaged drawer baskets or seals
Tripping electrics
Damaged condenser coils
And many more!
Book Your Fridge Freezer Repair in Nairobi
Whether you need an integrated, freestanding, or American style fridge freezer repair in Nairobi, Easy Repair Nairobi is here for you!
Why Book an Appliance Repair with Easy Repair Nairobi?
Here are six of the top reasons why we’re considered among the leading appliance repair companies in Nairobi:
Fast and Reliable
Our fast and reliable service sets us apart: we meet 99% of our same-day/next-day appointments in Nairobi!
Fully Stocked Vans
Why wait for a part? Your technician will arrive in a fully stocked van, minimising the need for repeat visits.
Transparent Prices
Our quotes include fixed labour fees, covering unlimited repair time and repeat visits, with only parts charged on top.
Nairobi’s Repair Specialists
We have a team of Nairobi-based engineers, meaning we can offer top-notch service – with a local touch.
Comprehensive Services
We repair washing machines, dishwashers, ovens, cookers, hobs, fridges, freezers, fridge freezers, tumble dryers and washer dryers!
1-Year Guarantees
Our 1-year parts and labour guarantees mean that you’ll enjoy total peace of mind when you choose Easy Repair Nairobi.
We Repair Washing Machines for our clients in Nairobi. Call us for the best, most reliable and affordable repair services including : Washing Machine Repair Services in Nairobi, Washing Machine Installation, Washer Maintenance, Washing Machine Parts and Spares Replacement in Nairobi Kenya
Need your washing machine repaired by trusted experts?
You’ve come to the right place. Our engineers have specialist knowledge of all washing machines allowing them to provide you with a quick, efficient and professional service.
Same-Day Washing Machine Repairs in Nairobi
Broken washing machine? For a fast and affordable solution, there’s only one choice: Easy Repair Nairobi’s Nairobi washing machine repair service
Same-Day Washing Machine Repairs
It’s estimated that the average family of four generates 10 loads of washing a week – so if your washing machine breaks down, the laundry can soon pile up. But with a team of twenty Nairobi-based engineers on standby, we can offer you a same-day washing machine repair service in Nairobi and the surrounding areas.
Evening/Weekend Appointments
We know that life doesn’t stop just because your washing machine’s broken. That’s why we offer evening and weekend appointments at no extra cost. We’ll even provide you with a convenient 2-hour time slot, and your engineer will call 30 minutes before arrival.
Highly Skilled, Fully Equipped Engineers
You can be confident that your engineer will possess all the skills and experience needed to complete the job. We’ll also do everything possible to ensure they have the right parts to hand; each Easy Repair Nairobi engineer works from a fully stocked van, while we hold further stock in our local warehouse.
Washing Machine Repair Near Me
If you’re searching for ‘washing machine repair near me’, then you’re probably looking for a local company. Easy Repair Nairobi is one of the leading independent appliance repair companies in Nairobi, as such, we can provide you with more than just a same-day washing machine repair; we can promise you a reliable, trustworthy, local service.
Ongoing Support
Our customers enjoy complete peace of mind thanks to our 1-year parts and labour guarantees. And our local approach and comprehensive appliance repair service means that we can look after all your major household appliances. We’re confident that once you’ve experienced the Easy Repair Nairobi difference, you’ll never want to use another Nairobi appliance repair company again!
Common Problems
Since 2012, we’ve performed thousands of washing machine repairs in Nairobi. During that time, we’ve come to recognise that some washing machine problems are more common than others. Below are three of the washing machine faults we see the most.
Failure to Spin
Your washing machine should be on a flat, stable area of the floor, and you should try to mix a variety of different-sized items. If your washing machine still fails to spin, then you’ll need a professional washing machine repair engineer to establish the cause of the problem.
Leaks
Your washing machine may be leaking due to a simple thing like a broken seal around the door, but it could also be a sign of a fault deeper inside the machine. Either way, electricity and water don’t mix, so even a minor leak should be professionally repaired immediately.
Excessive Noise
Washing machines aren’t the quietest appliances, but if yours has become noisier, that could be a sign of a problem. If your machine is level, stable, and not overloaded, then excessive noise could indicate an issue like worn bearings or a trapped coin in the inner drum.
Other Washing Machine Faults We Repair
This list covers other common Washing Machine faults we repair:
Blocked pumps
Dead machines
No drum rotation
Poor wash results
Problems with the spin cycle
Not draining
Faulty door
Not heating
Display error codes
Pressure system faults
Broken soap dispensers
Door seals/door gasket replacements
Bad smells
Snapped belts
Brands We Repair
We repair washing machines made by all the top manufacturers, including AEG, Amica, Ariston, Baumatic, Bauknecht, Beko, Belling, Blomberg, Bosch, Candy, Caple, CDA, Daewoo, De Dietrich, Electrolux, Fisher & Paykel, Gorenje, Hoover, Hotpoint, Haier, Hisense, Indesit, LG, Lamona, Miele, Neff, Siemens, Samsung, Smeg, Stoves, Whirlpool, Zanussi – and many more.